查看“MIPI-DSI液晶适配”的源代码

=原理=
MIPI液晶屏首先需要对屏驱动IC进行初始化，写入相关指令数据，然后CPU的液晶控制器按照设定的图像时序参数向驱动IC输出图像数据。所以移植需要屏参（时序参数HBP、VBP一类的）和初始化代码两部分。
=屏参修改=
对于A33/A64/A40i需要找到FEX文件中找到lcd0参数块；对于A133需要在DTS里找到lcd0节点；以FEX文件为例：

[lcd0]

lcd_used             = 1


lcd_driver_name      = "AML080WQ05"

lcd_backlight        = 100

lcd_if               = 4

lcd_x                = 800

lcd_y                = 1280

lcd_width            = 223

lcd_height           = 125

lcd_dclk_freq        = 70

lcd_pwm_used         = 1

lcd_pwm_ch           = 0

lcd_pwm_freq         = 200

lcd_pwm_pol          = 0

lcd_pwm_max_limit    = 255

lcd_hbp              = 40

lcd_ht               = 888

lcd_hspw             = 12

lcd_vbp              = 20

lcd_vt               = 1320

lcd_vspw             = 4

lcd_lvds_if          = 0

lcd_lvds_colordepth  = 0

lcd_lvds_mode        = 0

lcd_frm              = 1

lcd_hv_clk_phase     = 0

lcd_hv_sync_polarity = 0

lcd_dsi_if           = 0

lcd_dsi_lane         = 4

lcd_dsi_format       = 0

lcd_dsi_te           = 0

lcd_gamma_en         = 0

lcd_bright_curve_en  = 0

lcd_cmap_en          = 0


lcd_driver_name为初始化代码的名字，后面会提到；lcd_if=4表示使用DSI显示接口；lcd_x/lcd_y/lcd_dclk_freq/lcd_hbp/lcd_ht/lcd_hspw/lcd_vbp/lcd_vt/lcd_vspw这9个参数需要对照液晶面板Datasheet上标注的参数对应填好；lcd_dsi_if/lcd_dsi_lane/lcd_dsi_format/lcd_dsi_te这4个参数对照上文填好即可，无需变动；


对于电源/引脚配置：

A33：确保有lcd_power           = "axp22_dc1sw"这项即可；lcdd0~23/lcdclk/lcdde/lcdhsync/lcdvsync/[lcd0_suspend]块无用都可以删去；

A64/A40i：确保有lcd_power            = "vcc-mipi"和lcd_fix_power        = "vcc-dsi-33"，lcd_power为核心板VCC-MIPI输出（默认3V3），lcd_fix_power为CPU的DSI-Bank供电；lcdd0~23/lcdclk/lcdde/lcdhsync/lcdvsync/[lcd0_suspend]块无用都可以删去；

A133:确保有lcd_pin_power        = "dcdc1"和lcd_power            = "dc1sw"即可；确保引脚配置为pinctrl-0            = <&dsi4lane_pins_a>和pinctrl-1            = <&dsi4lane_pins_b>即可。

=U-Boot部分修改=
代码位置：

=Kernel部分修改=

=常见问题=